This is a working overview of RP-HPLC, written for readers who want more than a one-paragraph summary but less than a textbook.
This page was last updated on 2025-04-24 and is reviewed periodically as new material appears.
Purity and potency are related but distinct concepts in peptide testing. Purity describes the proportion of the main peptide relative to other detected substances, while potency refers to the biological or functional activity of a defined amount. A highly pure peptide can still have low potency if it is misfolded, aggregated, or chemically modified at a critical residue. Conversely, a less pure preparation may retain high activity if the impurities are inactive. Clear reporting separates these attributes and states the assay used for each.
Peptide purity specifications describe which tests define an acceptable lot and how results are reported. A certificate of analysis commonly lists a reverse-phase HPLC purity value, a mass spectrometry identity result, water content, counterion content, and residual solvent data. The specification may set a minimum area percent, such as 95% or 98%, depending on the intended use and grade. No universal threshold applies to all peptides, because sequence length, hydrophobicity, and manufacturing route influence achievable purity.
Reported purity values can differ between laboratories even for the same sample. Variations arise from column chemistry, mobile-phase composition, gradient slope, detection wavelength, injection load, and integration rules. Area percent also assumes that all species have similar response factors, which is not always true. Method validation examines specificity, linearity, accuracy, precision, limit of detection, and limit of quantitation. When comparing certificates, the method description and representative chromatogram are as important as the headline percentage.
Other methods address specific purity concerns. Amino acid analysis gives compositional data after hydrolysis, while capillary electrophoresis separates by charge-to-mass ratio. Karl Fischer titration measures residual water, and gas chromatography can detect residual solvents. Nuclear magnetic resonance can identify organic impurities but is less sensitive for trace levels. No single test covers all possible impurities, so purity testing usually combines orthogonal methods and reports the conditions used. The choice of methods is guided by the impurity classes of interest.
Reverse-phase high-performance liquid chromatography (RP-HPLC) is widely used to estimate peptide purity. It separates components by hydrophobicity on a column with a water-organic mobile phase. Ultraviolet absorbance at 214 nm or 220 nm detects peptide bonds. The main peak area as a percentage of total peak area gives a purity figure. This figure depends on column, gradient, wavelength, and how peaks are integrated, so it is method-specific rather than absolute.
Mass spectrometry provides complementary information by measuring molecular mass. Electrospray ionization or matrix-assisted laser desorption/ionization can confirm the expected peptide mass and reveal related impurities with different masses. It does not directly quantify all species because ionization efficiency varies. When coupled to liquid chromatography, LC-MS can assign masses to chromatographic peaks. This helps distinguish target peptide from truncation, oxidation, or deletion products. Mass accuracy and resolution determine how confidently a mass can be matched to a proposed structure.
| Property | Value | Notes |
|---|---|---|
| Typical purity specification | 95% or 98% area by RP-HPLC | Grade and application dependent |
| Common identity test | Electrospray ionization mass spectrometry | Confirms molecular mass |
| Typical water content method | Karl Fischer titration | Reports residual moisture |
| Common counterion test | Ion chromatography | Detects trifluoroacetate or acetate |
| Typical validation elements | Specificity, linearity, precision, accuracy | Follows method-validation guidance |
Vaccine therapies are a type of specific active immunotherapy. Vaccine therapies deliver various agents that will lead to a specific immune response e.g. antibody development or CTL response. Tumor antigens have been a main target in specific active immunotherapy by way of vaccination. Tumor antigens are antigens produced by tumor cells and can be common among patients with the same cancer-type, or unique to a particular patient. Their specificity to malignant tumor cells makes tumor antigens ideal candidates for vaccination. Cancer vaccine C-Met#Active immunotherapy, Mantle cell lymphoma Immunotherapy,
3′,5′-cyclic AMP + diphosphate It has key regulatory roles in essentially all cells. It is the most polyphyletic known enzyme: six distinct classes have been described, all catalyzing the same reaction but representing unrelated gene families with no known sequence or structural homology. The best known class of adenylyl cyclases is class III or AC-III (Roman numerals are used for classes). AC-III occurs widely in eukaryotes and has important roles in many human tissues. All classes of adenylyl cyclase catalyse the conversion of adenosine triphosphate (ATP) to 3',5'-cyclic AMP (cAMP) and pyrophosphate. Magnesium ions are generally required and appear to be closely involved in the enzymatic mechanism. The cAMP produced by AC then serves as a regulatory signal via specific cAMP-binding proteins, either transcription factors, enzymes (e.g., cAMP-dependent kinases), or ion transporters.
Enzymatic specificity provides useful insight into enzyme structure, which ultimately determines and plays a role in physiological functions. Specificity studies also may provide information of the catalytic mechanism. Specificity is important for novel drug discovery and the field of clinical research, with new drugs being tested for its specificity to the target molecule in various rounds of clinical trials. Drugs must contain as specific as possible structures in order to minimize the possibility of off-target affects that would produce unfavorable symptoms in the patient. Drugs depend on the specificity of the designed molecules and formulations to inhibit particular molecular targets. Novel drug discovery progresses with experiments involving highly specific compounds. For example, the basis that drugs must successfully be proven to accomplish is both the ability to bind the target receptor in the physiological environment with high specificity and also its ability to transduce a signal to produce a favorable biological effect against the sickness or disease that the drug is intended to negate.
The 3D structure of human serum albumin has been determined by X-ray crystallography to a resolution of 2.5 ångströms (250 pm). Albumin is a 65–70kDa protein. Albumin comprises three homologous domains that assemble to form a heart-shaped protein. Each domain is a product of two subdomains that possess common structural motifs. The principal regions of ligand binding to human serum albumin are located in hydrophobic cavities in subdomains IIA and IIIA, which exhibit similar chemistry. Structurally, the serum albumins are similar, each domain containing five or six internal disulfide bonds. Worldwide, certain traditional Chinese medicines contain wild bear bile, banned under CITES legislation. Dip sticks, similar to common pregnancy tests, have been developed to detect the presence of bear albumin in traditional medicine products, indicating that bear bile had been used in their creation. Albumin is pronounced ; formed from Latin: albumen "egg white", itself derived from the Latin albus: white.
Absolute specificity can be thought of as being exclusive, in which an enzyme acts upon one specific substrate. Absolute specific enzymes will only catalyze one reaction with its specific substrate. For example, lactase is an enzyme specific for the degradation of lactose into two sugar monosaccharides, glucose and galactose. Another example is Glucokinase, which is an enzyme involved in the phosphorylation of glucose to glucose-6-phosphate. It is primarily active in the liver and is the main isozyme of Hexokinase. Its absolute specificity refers to glucose being the only hexose that is able to be its substrate, as opposed to hexokinase, which accommodates many hexoses as its substrate.
Sources: en.wikipedia.org
Cannabis Analytical Science Program (CASP) is a forum where the science of hemp and cannabis analysis can be discussed and cannabis standards and methods developed. Analytical Solutions Forum (ASF) brings global stakeholders together to identify emerging needs and technologies in scientific analysis of food and related products. === Botanical Ingredients and Dietary Supplement Integrity Program === AOAC’s Botanical Ingredient and Dietary Supplement Integrity (BIDSI) Program focuses on coordinating all future consensus-driven need for development, validation, and implementation of methods for the analysis of a wide range of botanical ingredients and dietary supplements. === Stakeholder Program on Infant Formula and Adult Nutritionals === Stakeholder Program on Infant Formula and Adult Nutritionals program (SPIFAN) develops consensus-based standards and methods to make infant formula and adult nutritionals safer for babies and adults to consume.
Helices observed in proteins can range from four to over forty residues long, but a typical helix contains about ten amino acids (about three turns). In general, short polypeptides do not exhibit much α-helical structure in solution, since the entropic cost associated with the folding of the polypeptide chain is not compensated for by a sufficient amount of stabilizing interactions. In general, the backbone hydrogen bonds of α-helices are considered slightly weaker than those found in β-sheets, and are readily attacked by the ambient water molecules. However, in more hydrophobic environments such as the plasma membrane, or in the presence of co-solvents such as trifluoroethanol (TFE), or isolated from solvent in the gas phase, oligopeptides readily adopt stable α-helical structure. Furthermore, crosslinks can be incorporated into peptides to conformationally stabilize helical folds. Crosslinks stabilize the helical state by entropically destabilizing the unfolded state and by removing enthalpically stabilized "decoy" folds that compete with the fully helical state. It has been shown that α-helices are more stable, robust to mutations and designable than β-strands in natural proteins, and also in artificially designed proteins.
B cells can internalize antigen that binds to their B cell receptor and present it to helper T cells. Unlike T cells, B cells can recognize soluble antigen for which their B cell receptor is specific. They can then process the antigen and present peptides using MHC class II molecules. When a T helper cell with a TCR specific for that peptide binds, the B cell marker CD40 binds to CD40L on the T cell surface. When activated by a T cell, a B cell can undergo antibody isotype switching, affinity maturation, as well as formation of memory cells.
As the salt of a weak base (ammonium) and a weak acid (acetic acid), is often used to create a buffer solution. Ammonium acetate is volatile at low pressures. Because of this, it has been used to replace cell buffers that contain non-volatile salts in preparing samples for mass spectrometry. It is also popular as a buffer for mobile phases for HPLC with ELSD and CAD-based detection for this reason. Other volatile salts that have been used for this include ammonium formate. When dissolving ammonium acetate in pure water, the resulting solution typically has a pH of 7, because the equal amounts of acetate and ammonium neutralize each other. However, ammonium acetate is a dual component buffer system, which buffers around pH 4.75 ± 1 (acetate) and pH 9.25 ± 1 (ammonium), but it has no significant buffer capacity at pH 7, contrary to common misconception.
Gingras research focuses on the development of experimental and bioinformatics approaches for functional proteomics, with a focus on protein-protein and proximity interactions. She applies these tools to the study of signaling pathways in health and disease and in mapping the physical organization of the dynamic proteome. Some of her work focuses on the consequence of disease-associated mutations on the interactions established by proteins. In addition to proteomics, Gingras laboratory has interest in studying human protein phosphatase and their systematic interactions and has now expanded into the field of systems biology.
Sources: en.wikipedia.org
From 2002 to 2004, Pinhasov carried out postdoctoral research at Johnson & Johnson Pharmaceutical Research and Development (Spring House, Pennsylvania, United States), where under the guidance of Dr. Douglas Brenneman he was engaged in the development of drugs for the treatment of neurodegenerative diseases. In 2005, Pinhasov joined the Department of Molecular Biology at Ariel University (formerly the College of Judea and Samaria) as an assistant professor. He was Head of the department from 2008 to 2014. In 2014, Pinhasov was appointed Vice-President and Dean of Research & Development at Ariel University, holding this position until 2020. In 2020 the Senate of Ariel University elected Professor Pinhasov as the Rector of Ariel University, succeeding Professor Michael Zinigrad, who held this office for 12 years. In September 2023, in recognition of his contribution to academic ties between Israel and Kazakhstan, the Senate of Astana Medical University (AMU) awarded Prof. Albert Pinhasov the title of honorary professor.
Coiled-coil α helices are highly stable forms in which two or more helices wrap around each other in a "supercoil" structure. Coiled coils contain a highly characteristic sequence motif known as a heptad repeat, in which the motif repeats itself every seven residues along the sequence (amino acid residues, not DNA base-pairs). The first and especially the fourth residues (known as the a and d positions) are almost always hydrophobic; the fourth residue is typically leucine – this gives rise to the name of the structural motif called a leucine zipper, which is a type of coiled-coil. These hydrophobic residues pack together in the interior of the helix bundle. In general, the fifth and seventh residues (the e and g positions) have opposing charges and form a salt bridge stabilized by electrostatic interactions. Fibrous proteins such as keratin or the "stalks" of myosin or kinesin often adopt coiled-coil structures, as do several dimerizing proteins. A pair of coiled-coils – a four-helix bundle – is a very common structural motif in proteins. For example, it occurs in human growth hormone and several varieties of cytochrome. The Rop protein, which promotes plasmid replication in bacteria, is an interesting case in which a single polypeptide forms a coiled-coil and two monomers assemble to form a four-helix bundle.
Across several benchmarks, AlphaFold3 has demonstrated, on average, superior performance to conventional search-based docking algorithms in predicting small-molecule–protein binding modes. AlphaFold 3 version can predict structures of protein complexes with a very limited set of selected cofactors and co- and post-translational modifications. Between 50% and 70% of the structures of the human proteome are incomplete without covalently-attached glycans. Studies have shown that although AlphaFold3 can jointly model protein–ligand co-folding, its accuracy drops markedly on test cases with low similarity to its training data—an area of particular importance for drug discovery. Other work has found that AlphaFold is insensitive to adversarial decoys generated by altering the physicochemical properties of binding pockets, suggesting potential reliance on training-set memorization rather than genuine chemical awareness.
RGD and other bioactive ligands can be presented on the surface of a biomaterial in a number of different spatial arrangements, and it has been demonstrated that these arrangements have a significant impact on cell behavior. In self-assembled monolayers, it was found that adhesion and proliferation of both human umbilical vein endothelial cells (HUVECs) and human mesenchymal stem cells (MSCs) increased as a function of RGD peptide density. These studies also showed that RGD density could change integrin expression, which has been postulated to enable control of biochemical signaling pathways. Further investigation of MSCs on self-assembled monolayers showed that modulating RGD density and the affinity of RGD for αvβ3 (through use of linear and cyclized RGD) could be used to control the differentiation of MSCs. The effect of RGD presentation on cells in 3D biomaterials, which more accurately replicate the in vivo environment, has also been evaluated. In degradable polyethylene glycol hydrogels, the length of capillary-like structures formed by HUVECs was directly proportional to the density of RGD in the hydrogel. Additionally, studies in nano-patterning have shown that, whereas an increase in global RGD density increases cell adhesion strength until saturation, an increase in local (mico/nano-scale) RGD density does not follow this trend.
Sources: en.wikipedia.org
Purity percentages vary because each laboratory uses its own column, mobile phase, gradient, detection wavelength, and integration settings. A 95% value from one method may not equal 95% from another method. Comparative assessment requires the same validated procedure or an orthogonal cross-check.
A useful certificate of analysis states the peptide sequence, lot number, test methods, acceptance criteria, and measured results. It typically reports HPLC purity, mass spectrometry identity, water content, counterion content, and residual solvents when relevant. The document should also include a chromatogram and the date of testing.
Higher HPLC purity reduces the relative amount of ultraviolet-detectable impurities, but it does not guarantee correct sequence, stereochemistry, or biological activity. Some impurities may be invisible to the chosen method, and aggregates or counterions may still be present. Fitness for purpose depends on the intended application and the full set of tests.
It usually refers to the relative area of the main peak in a chromatographic separation, such as RP-HPLC. It estimates the proportion of UV-absorbing material in that peak, not the absolute mass fraction of the target peptide. Different methods can give different percentages.