mass spectrometry comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Updated 2026-02-20. Numbers and descriptions here follow the published literature rather than marketing material.
Additional techniques address components that reversed-phase chromatography may not resolve. Ion-exchange chromatography separates by charge, size-exclusion chromatography detects aggregates, and capillary electrophoresis offers high separation efficiency. Water content is measured by Karl Fischer titration, residual solvents by gas chromatography, and elemental impurities by inductively coupled plasma mass spectrometry. Amino acid analysis or nitrogen determination can estimate peptide content on a mass basis. Purity is frequently reported as area percent, yet standardized comparison across laboratories remains an open question because methods and reporting practices differ.
Peptide purity testing measures how much of a sample consists of the intended peptide sequence compared with related substances, water, counterions, and residual solvents. No single analytical method captures all of these components at once. Reversed-phase high-performance liquid chromatography with ultraviolet detection is widely used because it separates peptides by hydrophobicity. The reported purity value therefore depends on the chosen method, column, mobile phase, and detection wavelength. Established practice treats purity as method-dependent rather than an absolute property of the material.
Chromatographic separation resolves truncated, oxidized, deamidated, and epimerized peptide variants when their retention times differ from the target. Mass spectrometry confirms molecular mass and can reveal modifications that UV detection misses. Liquid chromatography coupled to mass spectrometry combines separation with identity information, which helps distinguish a pure target from a co-eluting impurity. UV-based area percent can overestimate purity if an impurity lacks a chromophore or if the target and impurity have similar response factors. Researchers often report both chromatographic purity and mass confirmation to give a fuller picture.
Handling practices strongly affect measured purity and sample integrity. Many peptides are hygroscopic, susceptible to oxidation, or prone to adsorption on glass and plastic surfaces. Lyophilized powders are typically stored desiccated at -20 °C or below, while solutions may require colder storage and minimized freeze-thaw cycles. Peptides containing cysteine, methionine, or tryptophan can degrade through oxidation or disulfide exchange. Working aliquots reduce repeated exposure to moisture and temperature fluctuations during routine analysis.
Purity values do not necessarily predict biological potency. Net peptide content corrects for counterions such as acetate or trifluoroacetate, water, and residual salts. Impurity thresholds for reporting, identification, and qualification are often set according to regulatory guidance, though specific limits depend on the product class and route of administration. Open questions remain about the toxicological relevance of low-level peptide impurities and about how best to compare results across different analytical platforms. A certificate of analysis should state the methods used and the basis for each reported value.
Peptide purity testing sits within a broader quality control framework. Release testing commonly includes appearance, identity, purity, peptide content, counterion content, water content, and residual solvents. Elemental impurities and microbiological attributes may be examined when relevant to the manufacturing route. Pharmacopoeial monographs and general chapters provide methods and acceptance criteria for some peptides, but many research-grade materials are not covered by such standards. Method validation establishes specificity, linearity, accuracy, precision, range, and robustness for each test.
| Property | Value | Notes |
|---|---|---|
| Appearance | White to off-white powder | Lyophilized peptides commonly appear as powders; color can vary with sequence. |
| Solubility class | Variable; often soluble in water or aqueous buffer | Depends on sequence, charge, and hydrophobicity. |
| Typical storage temperature | -20 °C or lower | Desiccated and protected from light; avoid repeated freeze-thaw cycles. |
| Typical analytical method | Reversed-phase HPLC with UV detection | Often paired with mass spectrometry for identity confirmation. |
| Common synonyms | Peptide purity analysis; peptide purity assay | Used in certificate of analysis and quality control contexts. |
Peptide purity specifications describe the minimum acceptable result from a defined test. A certificate of analysis may list HPLC purity, mass spectrometry identity, appearance, and counterion content. Specifications are method-dependent, so a value obtained with one gradient or wavelength may differ from another. For research use, common thresholds include 95% and 98% by RP-HPLC, but the appropriate limit depends on the application. The specification should always name the analytical method and acceptance criterion.
Quality control includes system suitability, blank injections, and reference standards. System suitability checks column performance and retention time reproducibility, while blank runs detect carryover or mobile-phase contaminants. Reference standards help calibrate retention time and detector response. Without these controls, a purity value is difficult to compare across laboratories or over time. Documentation of instrument settings and integration parameters is also part of quality control, and acceptance criteria should be set before samples are analyzed.
Mass spectrometry provides an identity check that complements chromatographic purity. Electrospray ionization or matrix-assisted laser desorption/ionization measures the mass-to-charge ratio of intact peptides. A match to the expected molecular mass supports correct sequence length and terminal groups. Mass accuracy alone does not prove that every peak in a liquid chromatogram is the target peptide. It also does not directly quantify how much water or counterion remains in a lyophilized powder.
Orthogonal methods reduce the chance that a single technique misses an impurity. Capillary electrophoresis separates by charge-to-size ratio and can resolve variants that co-elute under one set of HPLC conditions. Amino acid analysis reports composition after hydrolysis and confirms the presence of expected residues. Karl Fischer titration measures water content, while ion chromatography can quantify counterions. No single number captures all aspects of sample quality, so reports often combine several measurements.
Peptide purity testing uses separation methods to estimate the proportion of a sample that corresponds to the target sequence. Reverse-phase high-performance liquid chromatography is the most common technique, separating peptides by hydrophobicity on a nonpolar column. Ultraviolet detection at 214 nm records peptide bonds and aromatic residues. The resulting chromatogram is reported as area percent, which reflects relative absorbance rather than absolute mass. This distinction matters because water, counterions, and residual solvents do not appear in the peptide peak.
Handling practices reduce the risk of contamination and degradation. Hygroscopic peptides should be equilibrated to room temperature before opening to prevent condensation on the powder. Weighing and reconstitution in a controlled environment limit exposure to moisture and airborne particles. Aliquotting reconstituted solutions avoids repeated freeze-thaw cycles that can cause aggregation or precipitation. When a purity specification is not met, investigation may consider synthesis byproducts, purification losses, storage conditions, and analytical variability rather than a single cause.
Peptide purity can change during storage, handling, and reconstitution, and lyophilized peptides are generally more stable than solutions because water promotes hydrolysis and aggregation. Residual moisture, oxygen, and trace metals can accelerate degradation even in solid form. Temperature fluctuations during shipping may cause condensation and local moisture uptake. Quality control therefore includes appearance, water content, and analytical testing before and after storage challenges. Peptides containing cysteine, methionine, or tryptophan are especially susceptible to oxidation, while asparagine and glutamine residues can deamidate under neutral or alkaline conditions.
Analytical quality control compares a stored sample against a baseline profile. Reverse-phase chromatography remains common, but stability studies may also use mass spectrometry to detect oxidation, deamidation, or truncation products. Accelerated aging at elevated temperature can reveal degradation pathways, although extrapolation to room temperature is uncertain. Forced degradation studies expose peptides to heat, light, acid, base, and oxidants to identify likely breakdown products. Documentation should record lot number, storage history, and the exact method used for each measurement.
Regulatory frameworks treat peptide purity as part of product quality, though requirements vary by intended use and jurisdiction. Investigational materials may need identity, strength, quality, and purity documentation. Compendial monographs, when available, specify tests and acceptance criteria for certain peptides. For research peptides, oversight is often less prescriptive, and buyers may rely on supplier documentation. Open questions remain about how to standardize impurity reporting across laboratories and how to define purity for complex or modified peptides.
Quality control for peptide products relies on written procedures, batch records, and certificates of analysis. A certificate of analysis typically lists the test methods, specifications, and results for a specific lot. Batch records document synthesis, purification, and testing steps so that results can be traced to process conditions. Method validation establishes accuracy, precision, specificity, linearity, and limits of detection. These records support consistency across lots and allow laboratories to investigate deviations when a specification is not met.
C-reactive protein (CRP), a marker of systemic inflammation, is also increased in obstructive sleep apnea (OSA). CRP and interleukin-6 (IL-6) levels were significantly higher in patients with OSA compared to obese control subjects. Patients with OSA have higher plasma CRP concentrations that increased corresponding to the severity of their apnea-hypopnea index score. Treatment of OSA with CPAP (continuous positive airway pressure) significantly alleviated the effect of OSA on CRP and IL-6 levels.
Originally, seven such proteins were discovered. Of these, six (BMP2 through BMP7) belong to the Transforming growth factor beta superfamily of proteins. BMP1 is a metalloprotease. Since then, thirteen more BMPs, all of which are in the TGF-beta family, have been discovered, bringing the total to twenty. The current nomenclature only recognizes 13, as many others are put under the growth differentiation factor naming instead.
In molecular biology, the BtpA protein family is a family of proteins which includes BtpA. BtpA appears to play a role in the stabilisation of photosystem I. It is an extrinsic membrane protein located on the cytoplasmic side of the thylakoid membrane. Homologs of BtpA are found in the Thermoproteota and "Euryarchaeota", where their function remains unknown. The Ycf4 protein is firmly associated with the thylakoid membrane, presumably through a transmembrane domain. Ycf4 co-fractionates with a protein complex larger than PSI upon sucrose density gradient centrifugation of solubilised thylakoids. The Ycf3 protein is loosely associated with the thylakoid membrane and can be released from the membrane with sodium carbonate. This suggests that Ycf3 is not part of a stable complex and that it probably interacts transiently with its partners. Ycf3 contains a number of tetratricopeptide repeats (TPR); TPR is a structural motif present in a wide range of proteins, which mediates protein-protein interactions.
Cilengitide, a cyclic pentapeptide (RGDfV), is an investigational drug intended to block the growth of new blood vessels in tumors by interfering with the activation of integrin αVβ3. This integrin is upregulated in tumor and activated endothelial cells. This and other anti-angiogenic therapies depend on cutting off the blood supply to the tumor micro-environment, leading to hypoxia and necrosis. Cilengitide has been evaluated for the treatment of glioblastoma, but, as is the case for other anti-angiogenic therapies, has not been shown to alter progression or improve survival either alone or in combination with standard treatments. CEND-1, also known as iRGD, is a cyclic peptide that homes to tumors via binding to integrin alpha V receptors. It also binds and activates neuropilin-1, leading to a temporary opening of the tumor and an enhanced delivery of anti-cancer agents into the tumor tissue. It is currently being tested in clinical trials in solid tumor patients.
Sources: en.wikipedia.org
After translation, the AGP protein backbones are highly decorated with complex carbohydrates, primarily type II AG polysaccharides. The biosynthesis of the mature AGP involves cleavage of the signal peptide at the N-terminus, hydroxylation on the P residues and subsequent glycosylation and in many cases addition of a GPI-anchor. Glycosylation of the AGP backbone is suggested to initiate in the ERTooltip endoplasmic reticulum with the addition of first Gal by O-galactosyltransferase, which is predominantly located in ER fractions. Chain extension then occurs primarily in the GA. For those AGPs that include a GPI anchor, addition occurs while co-translationally migrating into the ER.
Afucosylated antibodies are intensely used in the field of advanced medicine, also due to their high ADCC (antibody-dependent cellular cytotoxicity). This makes them effective in binding to specific targets while minimizing damage to surrounding tissue. Some of the fields in which afucosylated antibodies are used or considered for application are: cancer immunotherapy autoimmune diseases Infectious diseases Furthermore, afucosylated antibodies are used as diagnostic tools and play a role in the development of personalized medications.
Aleksandar Zega (29 May 1860 – 29 March 1928) was a Serbian chemist. He held professional positions in the Government, Municipal and Customs Laboratories, and made a number of applied and theoretical contributions. He dealt with analytical and organic chemistry, specifically the analysis of mineral waters and foodstuffs. He studied and worked in Switzerland, however he wrote and published most of his works during his work and stay in Serbia. He was a contemporary of Milorad Z. Jovičić (1868–1937) and Wladimir Brunetti.
Sources: en.wikipedia.org
The Society recognizes achievements and promotes academic research through four annual awards. The Biemann Medal and the John B. Fenn Award for a Distinguished Contribution in Mass Spectrometry both are awarded in recognition of singular achievements or contributions in fundamental or applied mass spectrometry, with the Biemann Medal being focused on individuals who are early in their careers. The Ronald A. Hites Award is awarded for outstanding original research demonstrated in papers published in the Journal of the American Society for Mass Spectrometry. The Research Awards are given to young scientists in mass spectrometry, based on the evaluation of their proposed research. The Fellows of ASMS are awarded to individuals in recognition for their scientific contribution to mass spectrometry and for their contribution to the ASMS community. Journal of the American Society for Mass Spectrometry Measuring Mass: From Positive Rays to Proteins The past presidents of ASMS are:
The food industry is a major consumer of amino acids, especially glutamic acid, which is used as a flavor enhancer, and aspartame (aspartylphenylalanine 1-methyl ester), which is used as an artificial sweetener. Amino acids are sometimes added to food by manufacturers to alleviate symptoms of mineral deficiencies, such as anemia, by improving mineral absorption and reducing negative side effects from inorganic mineral supplementation. Amino acids are low-cost feedstocks used in chiral pool synthesis as enantiomerically pure building blocks. Amino acids are used in the synthesis of some cosmetics. The chelating ability of amino acids is sometimes used in fertilizers to facilitate the delivery of minerals to plants in order to correct mineral deficiencies, such as iron chlorosis. These fertilizers are also used to prevent deficiencies from occurring and to improve the overall health of the plants.
Nanoghosts are nanosized vesicles containing a chosen drug delivery payload manufactured from extracted leukocyte membranes with the cell cytoplasm content removed. The use of biological membranes serves to mask the particles from the immune system to reduce the likelihood of an immunogenic response, as well as to extend circulation of the particles in the blood. They are produced by homogenizing the cells to remove the cytosol, and then sonicating the empty cell membranes to create nanoghosts between 100 and 200 nm in diameter. Membranes used to make nanoghosts harvested form red blood cells have been shown to circulate for about 120 days and avoid phagocytotic cells. Neutrophil based nanoghosts retain the chemotaxis capacity of neutrophils to sites of inflammation, which encourages tumor targeting. NK based nanoghosts exhibit metastatic cancer targeting behavior. Monocyte based nanoghosts are effective at infiltrating the tumor microenvironment. Mesenchymal stem cell derived nanoghosts exhibit cancer targeting properties.
The main building of the Institute is located at the intersection of Kremlyovskaya and Lobachevskaya streets. This four-story building built in 1953 in the style of Soviet neoclassicism under the guidance of architect A.G. Bikchentaev. The building of the museum of Kazan chemical school is located in the campus of the main university building, built in the 1830s in a classical style under the guidance of architect M.P. Corinfskiy. In 2015 construction of a large laboratory building in the campus of Alexander Butlerov Institute of Chemistry was finished. The 7-storey building housed classrooms and laboratories of departments of Alexander Butlerov Institute of Chemistry, Institute of Geology and Petroleum Technologies, Institute of Physics. The building was constructed with the support of the President of Tatarstan R.N. Minnikhanov and PSC "TAIF".
Sources: en.wikipedia.org
It usually refers to the relative peak area of the target peptide in a chromatogram, not the mass fraction of the entire sample. Different analytical methods can yield different purity values. Water, counterions, and residual solvents are excluded unless the calculation specifies otherwise.
A single method can miss co-eluting impurities, salts, water, or structural modifications. Orthogonal techniques separate compounds by different properties, such as hydrophobicity, charge, or size. Combining results gives a more complete assessment of sample composition.
No, purity measures the amount of target relative to other peaks, not the identity or sequence of the target. Mass spectrometry and sequencing may be needed to confirm structure. A high-purity sample can still contain a peptide with an incorrect sequence.
Lyophilized peptides are generally stored desiccated at -20 °C or lower, protected from light and moisture. Solutions are often kept at -80 °C in aliquots to limit freeze-thaw damage. Specific sequences may require different conditions based on oxidation or aggregation risk.